All guides The SHOPOFLUX edit

How to Fit a Silicone Cover on a Wagon R 2-Button Key

Microfibre cloth and a keyring in a ceramic dish on a sunlit table, ready for fitting a key cover

To fit a silicone cover to a Wagon R two-button fixed-blade key, remove the keyring, line up the lock and unlock panels, then gently ease the sleeve over the plastic key head through its fitting opening. Seat the edges with your fingertips and check that both buttons release freely. The metal blade and the keyring opening should remain clear.

This guide uses the rounded two-button key shown below. Begin with the Maruti Suzuki collection, choose the 2-button remote-key design and compare it with your own key before fitting a cover.

Put your key beside this reference first

Front and back of a rounded Maruti Suzuki two-button key head with an exposed fixed blade and a keyring hole at one corner
Catalogue reference from the silicone-cover listing. Compare the rounded plastic head, the two button positions and the hole at the corner.

The fixed metal blade projects from one end of this key. The plastic head is broad and rounded, with two buttons on the front and a keyring hole at a corner. Hold your key in the same direction as the reference to compare all three details. If yours has a folding blade or a differently shaped head, use its matching design page before continuing.

The black silicone pack of two is listed for this remote-key shape and names Wagon R among its model references. Each key in a pair needs its own shape check, especially if one has had a replacement shell fitted.

Clear the table and line up the sleeve

Lay the key on a soft, dry cloth. Take off its old cover and detach the ring and any hanging accessories. Wipe loose dust from the key head. Keep the original key housing assembled throughout fitting.

Set the silicone sleeve beside the key. Identify its lock and unlock panels, the opening for the metal blade and the keyring hole. Turn the sleeve until these features line up with the key. The moulded button outlines give you a useful orientation check before you start.

Two black silicone sleeves with white lock and unlock symbols and an opening for the keyring at one corner
The two sleeves shown in the black pack have separate lock and unlock panels. Check their orientation against the key before fitting.

Ease the cover on a little at a time

  1. Find the fitting opening. Inspect the sleeve and any supplied fitting directions. Use the opening intended for inserting the key head. Keep the narrow keyring hole free from stretching.
  2. Support the plastic head. Hold the key securely and ease the sleeve over it with your fingertips. Work a small section of the lip around the edge at a time, keeping the button panels aligned. Keep tools away from the silicone.
  3. Seat the edges. Once the head is inside, gently smooth the sleeve around its perimeter. Check for a folded lip or a raised corner, particularly around the blade exit and keyring hole.
  4. Try both buttons. Press and release each button separately. Each should return when you lift your finger. If a panel stays depressed or the sleeve sits at an angle, remove it gently and check the orientation again.
  5. Refit the keyring last. Align the openings in the sleeve and the original key head. Feed the ring through the original keyring hole, keeping the silicone clear of the split in the ring.

If fitting requires a hard pull or a corner keeps lifting, pause and compare the bare key with the listing again. Check the inside of the sleeve for a folded edge. Ask for fit help before trying to alter the sleeve.

Check the key before you leave home

Check What to look for
Button response Lock and unlock each press and release independently, and the car responds as expected.
Blade clearance The sleeve sits around the plastic head with the metal blade exposed. It clears the ignition surround during normal use.
Keyring attachment The ring passes through the original key head, with the sleeve lying flat around the hole.
Edges The cover stays seated when you pick up the key and use its buttons.

Test locking and unlocking while you are beside the car, keeping access to the key. When checking the ignition, stop if the added sleeve catches against the surrounding trim. The key-cover fit checklist can help you identify which opening or edge needs another look.

Common fitting questions

Do I need to remove the screw on the back of my key?

The silicone sleeve goes over the assembled key head. Keep the key’s screw and housing in place. Any instructions for opening an accessory frame apply to that particular cover.

Can I use these steps for a metal key cover?

Use the assembly instructions for the exact metal cover you ordered. A frame with an inner insert and fasteners has its own fitting sequence. Open its product gallery and check the components before starting.

How do I remove the silicone sleeve later?

Detach the keyring, then gently ease the sleeve’s lip back along the fitting opening while supporting the plastic head. Work gradually around the edge. For cleaning after removal, follow the care guide by material and let the cover dry fully before refitting it.

If the shape still looks uncertain, use the fit-help option on the product page and send a clear front, back and side photo of the bare key. The silicone sleeve listing with colour options also includes a key reference to compare before choosing.

Previous
MG Key Cover Guide: Match Your Hector, Astor, ZS EV or Windsor EV Key